Posts by Dirk Broer

1) Message boards : Number crunching : Validator down 6th February 2024 (Message 4119)
Posted 146 days ago by Dirk Broer
radac_validator_v3 radioactive Not Running

Workunits waiting for validation 75,527
2) Message boards : Number crunching : Validator down 25th April 2023 (Message 4074)
Posted 443 days ago by Dirk Broer
Workunits waiting for validation 18,954
3) Message boards : Number crunching : Can't set location (Message 4056)
Posted 772 days ago by Dirk Broer
Congratulations, Saenger
Note your hostId is just about as high as mine, after I changed system.

4) Message boards : Number crunching : Can't set location (Message 4054)
Posted 782 days ago by Dirk Broer
In the end I solved it by attaching my sensor to another (Windows) system and even managed -don't ask me with which version of tried settings- to add my sensor on the map.

Latitude: ##.##### degrees North (of the Equator) - Longitude: ##.##### degrees East (of Greenwich)


seems too simplistic, you could also be South of the Equator and/or West of Greenwich, so I also tried with added N and E in my settings.
5) Message boards : Number crunching : Can't set location (Message 4049)
Posted 829 days ago by Dirk Broer
Does the manual method not work?

http://radioactiveathome.org/boinc/forum_thread.php?id=499&nowrap=true#4046



If it did my detector would have sprung to live on the project, but not a single detector is 'live' in the Netherlands at the moment -see map. The map also shows only one reactor here, while there are four, three active (Petten -experimental, Delft -educational, Borssele) and one deactivated (Dodewaard).
6) Message boards : Number crunching : Can't set location (Message 4047)
Posted 842 days ago by Dirk Broer
Can't set my location (in the Netherlands).
Not a single sensor in the Netherlands anymore, coincidence?
7) Message boards : Number crunching : Can't set location (Message 4033)
Posted 904 days ago by Dirk Broer
At least you have a graph and getting half credits. My sensor is lit up and working fine, but I can no longer run tasks for this project as it says there is no app which will run on my Linux box (it's lying, there is, I haven't changed the computer just upgraded to a newer version of Linux). So I have a pretty USB geiger counter and that's it. Nobody else can see it but me. It's a pity, this was a fun project while it had support, but I feel nobody has the technical knowledge to answer/fix these problems now. :(


An upgrade to a newer version of Linux may have removed needed files, or substituted newer versions without needed lines. What did you do in the previous version to get the project going?
8) Message boards : Number crunching : Can't set location (Message 4032)
Posted 904 days ago by Dirk Broer
Hello Saenger,

For me the 3rd is 19090 and the 4th is 15201
the 3rd is my user Id within the project, the 4th is the Id of my sensor.

but as you state it is impossible to enter values in the first two fields.
9) Message boards : Number crunching : Can't set location (Message 4029)
Posted 911 days ago by Dirk Broer
Yes, but at least the coordinates should be possible to insert

I have four fields, the first two empty. What am I supposed to give in as data?
10) Message boards : Number crunching : Validator down 20th November 2021 (Message 4011)
Posted 965 days ago by Dirk Broer
I hope the stats export will be enabled too....


Next 10 posts

Main page · Your account · Message boards


Copyright © 2024 BOINC@Poland | Open Science for the future