Posts by [AF>Libristes] cottesloe Add sensor

Posts by [AF>Libristes] cottesloe

1) Message boards : Cafe : Pending since 8th march??? (Message 3439)
Posted 2821 days ago by

Hi Folks,

All my UT since 8th march are in pending, and I'm not the only one in my team!

What Happen?

Thanks.

2) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3042)
Posted 3227 days ago by

Hi Szopler!

I checked in static, with an Ohmmeter, the continuity between USB and R5, R6, R7, Dz2, Dz3, IC1 pins 4 6 and 11, and it looks good. I didn't find any trouble.
I made my test with an USB cordless plugged.

What else?

3) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3039)
Posted 3228 days ago by

[AF>Libristes] cottesloe

Hi!

Always with the trouble with my two 2.60 kits.

Question to the specialists...
If I upgrade the firmware, is the problem will be resolved?

Best regards from France!

4) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3031)
Posted 3232 days ago by

[AF>Libristes] cottesloe

Same same...

§ lsusb -v -d 16c0:05df | grep 'iManufacturer'
§ iManufacturer 1
§ lsusb -v -d 16c0:05df | grep 'iProduct'
§ iProduct 2

5) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3029)
Posted 3232 days ago by

[AF>Libristes] cottesloe

Hi!
Yes, of course I can try again.
Is it necesary to reset the project?

6) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3022)
Posted 3234 days ago by

[AF>Libristes] cottesloe

Hello,

With the help of my AF's friend Elgrande, I found a problem with my kits.

§ lsusb -v -d 16c0:05df | grep 'iManufacturer'
§ iManufacturer 1
§ lsusb -v -d 16c0:05df | grep 'iProduct'
§ iProduct 2

Why I don't have a Manufacturer and a Product names?
Is it the reason why all WUs return

Warning: cannot query manufacturer for device: error sending control message: Broken pipe

??

Thank you to help me.

7) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3004)
Posted 3244 days ago by

[AF>Libristes] cottesloe

Hello,

I crossed my detectors to make a test.
The 2.60 detector on my Raspi (app version 1.78) said:

<core_client_version>7.0.27</core_client_version>
<![CDATA[
<stderr_txt>
nding control message: Broken pipe
Warning: cannot query manufacturer for device: error sending control message: Broken pipe
Warning: cannot query manufacturer for device: error sending control message: Broken pipe....

The same detector on my PC (app version 1.77) said:

<core_client_version>7.2.42</core_client_version>
<![CDATA[
<stderr_txt>
Radac $Rev: 585 $ starting...
Could not find any of the devices listed in sensors.xml: The specified device was not found
12:37:11 (3771): called boinc_finish

</stderr_txt>

Which app version I have to use with a 2.60 detector?

Thank you.

8) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3002)
Posted 3246 days ago by

[AF>Libristes] cottesloe

Well, I found a bad weld on a GND pin on IC2. Then, the detector show the same µSv/h rate than my first detector.
Thank you very much Szopler for your good intuition.

But now, the UT returns again the same message :

And the credit is 0.00 ...

I use a Raspi, and it works correctly with my first detector, so I don't know what to do?

9) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 3001)
Posted 3247 days ago by

[AF>Libristes] cottesloe

OK, I'll try this operation.

Thanks for your help!

10) Message boards : Cafe : KIT - Discussion [topic OPEN] (Message 2991)
Posted 3249 days ago by

[AF>Libristes] cottesloe

Hi!

I just finish to assembly a 2.60 kit, and I've got a problem.
The display show 0,00µSv/h everytime.
The Geiger tube is OK, I tested it in my old detector.
The voltages look good (190V around the tube, and 380V on the transfo).

The task returns:

Stderr output

<core_client_version>7.0.27</core_client_version>
<![CDATA[
<stderr_txt>
nding control message: Broken pipe
Warning: cannot query manufacturer for device: error sending control message: Broken pipe
Warning: cannot query manufacturer for device: error sending control message: Broken pipe
....

I don't think I made a mistake, so I don't know what to do now.

Greeting from France.

Next 10 posts