Posted 3058 days ago by gismoat
Hi all,
KarmannGaz have repaired my defect detector.
Big thanks to Gary for your support.
cheers
Werner
Posted 3076 days ago by gismoat
Dear Gary,
thanks for your Answer.
I have sent a PN to you.
thanks
Werner
Posted 3079 days ago by gismoat
Hallo,
ist zufällig jemand aus Deutschland/Österreich/Schweiz vertreten der mir weiter helfen kann?
Ich habe bei mir Zuhause nicht so viele Möglichkeiten meinen Detektor zu Reparieren. Weiteres bin ich im Elektrobreich nicht so versiert.Ich würde natürlich für die Kosten aufkommen. Bin auch bereit für die Arbeit eine kleinigkeit zu Zahlen.
Danke
Werner
Posted 3097 days ago by gismoat
Hi Szopler,
i have make a test with a insulated wire and just connect and disconnect few times. I do not got a detector beep's or diode blinks.
Could you be so kind anfd tell me where i can find the IC2 and witch tests i should be make?
thanks for your help.
Werner
Posted 3124 days ago by gismoat
my backside is clear but on the front side i have two orange resistors (C10, C13).
The both parts are on the same position as your DZ4 but not on the back side but its on front.
How many volt should have the DZ4?
Other questin: Could i mesure the R12 and R18 when i have turnd of the tube?
Because the both parts are under the tube.
Posted 3128 days ago by gismoat
Hi all,
i get my new tube and the new clips. I have installed and make a test but i get always 0,0 uSV :-(
Now i have no idea what can now broken.
Posted 3140 days ago by gismoat
Hi Norbert,
thanks for your info. I have now messure on the correct Pin3 and T1 transistor.
The resault is also 004.
The new Tube is maked as Shipped on 09.09.
Last Tracking was on 19.09, so i hope the Tube is comming soon.
I have read that i should not connect the new tube with a cable and solder directly. Do you know where i can order a clip for the tube?
A article number would be also helping.
thanks
Werner
Posted 3141 days ago by gismoat
Hello there,
@KarmannGaz: I have checked the resistor and i think that is normal. Two resistors is conected with solder (i hope this is the correct word)
So now i have make a messure again and i hope i maked correct.
First messure is Pin5 with transistor T3 and the resault was 004.
The next messure was Pin3 with transistor T1 and the resault was also 004.
I have turn off the Display so that i can make a better messure on the tube and the resistor. Now the resault is 204.
I have now realy an idea what i can do.
Only one think is i wait of my new tube is received and i could check is this the reason or not.
Or do you have any idea?
thanks
Werner
Posted 3146 days ago by gismoat
Hi Norbert,
thanks for your reply and your info.
I have now messure again but i get 0,0 Volt on the voltmeter.
Now how i can check witch part is defect?
I have written an email to Szopler 2 month ago for a maintenance but i dont get an answer.
Do you have any idea?
thanks
Werner
Posted 3154 days ago by gismoat
Hi all,
I am back from our Holiday.
I have order today a new Tube.
I have messure with my voltmeter.
I have use the red stick from the voltmeter and go on the resistors where i have marked in red and the black stick i go to the tube.
I saw on the voltmeter a value of 406.
Voltmeter setting as follow.
thanks
Werner